RockBoard MOD 1 V2 All-in-One TRS, XLR, IEC & DC Patchbay | No Limit Guitar Co, Idaho Falls
The RockBoard MOD 1 V2 is an all-in-one patchbay designed to consolidate every connection on your pedalboard into a single, organized access point — making setup and teardown at any gig a matter of seconds rather than minutes. Compatible with virtually all RockBoard pedalboards featuring MOD slots, as well as a wide range of boards from other manufacturers, the MOD 1 V2 is an essential organization upgrade for any serious gigging musician. Whether you're running a simple guitar-to-amp chain or a complex four-cable method rig, this patchbay keeps everything tidy, accessible, and permanently wired.
Product Overview
The MOD 1 V2 fits directly into the dedicated MOD slot found on most RockBoard pedalboards — including the Quad 4.2 — providing a flush, integrated mounting solution that keeps all your I/O neatly routed in one place. For players using pedalboards from other manufacturers, the removable front plate allows the module to be mounted on top of or underneath virtually any board using RockBoard's optional Mounting Rack.
The patchbay's pass-through design supports the four-cable method out of the box, allowing you to split your signal chain between pedals running in front of the amp (drives, compressors, filters) and pedals running in the effects loop (reverb, delay, modulation) — all organized through one central panel. The included XLR throughput also enables a direct signal output to a mixing console or PA system, making the MOD 1 V2 equally useful for players who go direct alongside or instead of a traditional amp.
All connections on the front panel are mirrored on the backside, so your permanently wired pedals stay neatly tucked underneath the board while the front panel presents clean, labeled jacks ready for your instrument cable, amp cables, and power connections. At 450g and fitting within a compact 160 x 60 x 33mm footprint, it adds minimal bulk to your existing setup. Idaho Falls guitarists shopping at No Limit Guitar Co will find the MOD 1 V2 pairs naturally with the RockBoard Quad 4.2 pedalboard.
Ideal For
- Gigging guitarists and bassists seeking a pedalboard cable management solution that speeds up stage setup
- Players running the four-cable method who need a clean, centralized I/O hub for amp and effects loop routing
- Live performers who send a direct XLR signal to a mixing console or PA from their pedalboard
- Musicians looking to upgrade any pedalboard — RockBoard or otherwise — with a professional patchbay system
- Touring players who keep their boards permanently wired and need fast, reliable connections at every show
Key Features
All-in-One Centralized I/O
The MOD 1 V2 brings five TRS, one XLR, one DC barrel, and one IEC AC connection into a single panel, eliminating the need to reach behind or underneath your board for individual pedal connections. Every cable you need for a full gig plugs into one organized strip.
Four-Cable Method Ready
The pass-through design supports the four-cable method natively, letting you route pre-amp pedals and effects loop pedals through one central point without complex cable routing behind the board. Swapping rigs or venues becomes significantly faster.
XLR Direct Output
The XLR throughput (male front / female back) provides a clean signal output from the pedalboard directly to a mixing console or PA — a practical feature for players who go direct, run wet/dry rigs, or perform in venues without backline.
Removable Front Plate for Universal Compatibility
The detachable front plate allows the MOD 1 V2 to be used with non-RockBoard pedalboards via RockBoard's Mounting Rack accessory. It can be positioned on top of or underneath the board depending on your setup and preference.
Mirrored Connections & Permanent Wiring
All front panel connections are mirrored on the backside, allowing your pedal cables to stay permanently wired and hidden underneath the board. Connections on the front are clean, consistent, and ready to plug in at a moment's notice.
What's Included
- RockBoard MOD 1 V2 All-in-One Patchbay
- Mounting screws, counter nuts, and TX wrench
- RockBoard by Warwick manufacturer warranty
- Note: Compatible with most RockBoard pedalboards with one or more MOD slots. Not compatible with the compact DUO series. Mounting Rack for non-RockBoard boards sold separately.
Technical Specifications
| Specification | Details |
|---|---|
| Connections (Front & Back) | 5 x 6.3mm / ¼" TRS thru, 1 x XLR thru (male front / female back), 1 x DC 2.1 x 5.5mm barrel thru, 1 x AC IEC thru (male front / female back) |
| Connection Layout | All connections mirrored on backside |
| MOD Slot Compatible | Yes (most RockBoard pedalboards; not DUO series) |
| Third-Party Compatibility | Yes, via removable front plate and optional Mounting Rack |
| Dimensions (excl. front plate) | 160 x 60 x 33mm / 6 19/64" x 2 23/64" x 1 19/64" |
| Front Plate Dimensions | 175 x 48mm / 6 57/64" x 1 57/64" |
| Weight | 450g / 0.99 lbs. |
| Included Hardware | Mounting screws, counter nuts, TX wrench |
Get Your Hands on This Pedalboard Patchbay Today
Stop by No Limit Guitar Co in Idaho Falls to see the MOD 1 V2 alongside our full RockBoard lineup, including the Quad 4.2 pedalboard it was made to pair with. Our team can help you map out a complete cable management solution for your specific rig and answer any questions about four-cable method routing or direct output options. Visit us in store or check availability on our website.
